Imposing accurate wall boundary conditions in corrective‐matrix‐based moving particle semi‐implicit method for free surface flow

Corrective matrix that is derived to restore consistency of discretization schemes can significantly enhance accuracy for the inside particles in the Moving Particle Semi‐implicit method. In this situation, the error due to free surface and wall boundaries becomes dominant. Based on the recent study on Neumann boundary condition (Matsunaga et al, CMAME, 2020), the corrective matrix schemes in MPS are generalized to straightforwardly and accurately impose Neumann boundary condition. However, the new schemes can still easily trigger instability at free surface because of the biased error caused by the incomplete/biased neighbor support. Therefore, the existing stable schemes based on virtual particles and conservative gradient models are applied to free surface and nearby particles to produce a stable transitional layer at free surface. The new corrective matrix schemes are only applied to the particles under the stable transitional layer for improving the wall boundary conditions. Three numerical examples of free surface flows demonstrate that the proposed method can help to reduce the pressure/velocity fluctuations and hence enhance accuracy further.     

Structural and phase characteristics of the diamond/matrix interfacial zone in high-resistant diamond composites

The structural-phase state of the contact zone and the factors that influence on the strength of diamond retention in the diamond carbide composites were determined. Composites were obtained by the new hybrid technology that eliminates the reheating of the metalized coating. The elaborated technology combines the thermal diffusion metallization of a diamond and the sintering by the scheme of self-dosed impregnation in a one-stage technological cycle. By the methods of electron microscopy, X-ray diffraction analysis, and Raman spectroscopy the structural and phase characteristics of the interphase boundary were investigated. The improvement of chemical and mechanical adhesion between the diamond and carbide matrix was obtained. It was shown that the specific productivity of the samples with a metalized diamond component is 39% higher than those without metallization.     

求解矩阵方程AXB+CXD=F参数迭代法的最优参数分析

本文针对求矩阵方程AXB+CXD=F唯一解的参数迭代法，分析当矩阵A，B，C，D均是Hermite正（负）定矩阵时，迭代矩阵的特征值表达式，给出了最优参数的确定方法，并提出了相应的加速算法.     

高居里温度铁电单晶PIN-PT的机电性能

弛豫铁电单晶Pb(In_1/2Nb_1/2)O₃-PbTiO₃(PIN-PT)相较于常用的Pb(Mg_1/3Nb_2/3)O₃-PbTiO₃(PMN-PT)具有更高的居里温度,在高稳定性、高性能的传感器、换能器方面具有应用前景。本工作采用谐振法研究了[001]方向极化的0.66PIN-0.34PT铁电单晶的全矩阵机电性能参数。0.66PIN-0.34PT 单晶的三方-四方相变温度(T_RT)约为160 ℃,居里温度(T_C)约为260 ℃,室温压电系数d₃₃、d₃₁、d₁₅分别为1 340 pC/N、-780 pC/N、321 pC/N,介电常数ε^T₃₃、ε^S₃₃、ε^T₁₁、ε^S₁₁分别为2 700、905、2 210、1 927,机电耦合系数 k₃₃、k₃₁、k₁₅、k_t分别为 87%、58%、38%、61%。其纵向压电常数(d₃₃)和纵向机电耦合系数(k₃₃)小于 PMN-PT 单晶,但是横向压电性能(d₃₁)和剪切压电性能(d₁₅)都略高于PMN-PT单晶。另外,研究了机电耦合性能随温度的变化趋势,发现0.66PIN-0.34PT单晶在150 ℃以下有较好的温度稳定性。